11330 - 70th Street, SE
Calgary, Alberta    1-888-254-6157

Calgary Scissor Lift Certification

Calgary Scissor Lift Certification - A lot of worksites and tradespeople like iron workers, welders and masons utilize scissor lift platforms in order to help them reach elevated work places. The use of a scissor lift is often secondary to their trade. Thus, it is essential that all platform operators be correctly trained and certified. Regulators, industry and lift manufacturers all work together to be able to make sure that operators are trained in safely utilizing work platforms.

Work platforms are likewise known as manlifts or AWPs. These equipment are stable and easy to operate, even though there is always some risk because they lift individuals to heights. The following are various key safety concerns common to AWPs:

There is a minimum safe approach distance (also known as MSAD) for all platforms in order to protect from accidental power discharge due to proximity to wires and power lines. Voltage can arc across the air and cause injury to workers on a work platform if MSAD is not observed.

To be able to ensure maximum steadiness, care should be taken when the work platform is lowered. When you move the load towards the turntable, the boom must be retracted. This would help maintain steadiness if the -platform is lowered.

The regulations regarding tie offs do not mandate individuals working on a scissor lift to tie themselves off. Several groups would on the other hand, require their employees to tie off in their employer guidelines, job-specific risk assessments or local regulations. The manufacturer-provided anchorage is the only safe anchorage wherein harness and lanyard combinations should be attached.

It is essential to observe and not go over the maximum slope rating. The grade can be measured by laying a straight edge on the slope or by laying a board. A carpenter's level can then be placed on the straight edge and raised until the end is level. By measuring the distance to the ground and dividing the rise by the length of the straight edge, then multiplying by 100, you could determine the percent slope.

A standard walk-around inspection must be carried out to determine if the unit is mechanically safe. A location assessment determines if the work place is safe. This is vital particularly on changing construction sites because of the possibility of obstacles, contact with power lines and unimproved surfaces. A function test should be done. If the unit is utilized properly and safely and correct shutdown measures are followed, the possibilities of accidents are greatly reduced.

Click to Download the pdf



Forklift Certification Courses

  • Calgary Crane Ticket
    Calgary Crane Ticket - Modern cranes can either be simple or complex, based upon the nature of the use they could perform. For example, mobile cranes are rather simple units. A telescopic boom and even a steel truss mounts its movable platform. A ...
    More
  • Calgary Forklift Operator Certification
    Calgary Forklift Operator Certification - Forklift operator certification is usually needed for employees working in construction, warehouse or industrial environments to ensure the safe operation of forklifts. Workplace training must follow a ...
    More
  • Calgary Crane Operator Classes
    Calgary Crane Operator Classes - For the supervisors and the operators, new and current, the crane operator training course is suitable for all. Course content addresses relevant state, federal and provincial safety regulations. The first part of ...
    More
  • Calgary Heavy Equipment Training School
    Calgary Heavy Equipment Training School - The heavy equipment operator courses will assist the operator in obtaining the necessary knowledge and skills they will need in order to enter the workforce as an entry level operator. In this 12 week ...
    More
  • Calgary Scissor Lift Operator Certification
    Calgary Scissor Lift Operator Certification - Regulations within North America normally suggest that operators of booms, scissor lifts or aerial work platforms all acquire operator certification. Scissor lift operator certification is not ...
    More
  • Calgary Aerial Boom Lift Training
    Calgary Aerial Boom Lift Training - For people who operate or supervise the utilization of aerial lift platforms, right aerial boom lift Training is required. The aerial lift platform is used for lifting individuals, tools and materials to ...
    More
  • Crane Certification - Overhead Crane, Self-Erect Crane, Truck Mounted Crane, Hydraulic Cranes Certification in Calgary
    Overhead cranes are otherwise called bridge cranes. They are a kind of crane that consists of a hook and line mechanism that runs along a horizontal beam which runs along two widely separated rails. Various overhead cranes could be seen inside a ...
    More
  • Calgary Loader Operator Certification
    Calgary Loader Operator Certification - Why You Need to Obtain A Loader Operator Certification - Certification for forklifts are required to ensure the safe utilization of forklifts for those employers in industrial, warehouse or construction ...
    More

Forklift Certification Calgary

Our large number of programs should ensure that you will find the right one for you or your personnel. Additionally, we offer you two options for training. We can provide it on-site or at our place of operations. Our experienced team can tailor our instruction to your specific equipment at your location of operations.

TOLL FREE: 1-888-254-6157
11330 - 70th Street, SE
Calgary, Alberta    T2C 4Y3

www.forkliftcertificationcalgary.com

Email Us